Tri Tool
The weld starts
with the prep.
Tri Tool builds portable machine tools that cut, face, square and bevel pipe and tube to a machined finish — no torch, no heat affected zone, no grinding to fix it afterward. Square ends and consistent land is what makes an orbital weld repeatable. This is the front half of that job.
We carry it, we support it, and we service and calibrate it — in our shop or on your floor.
info@tigcompany.com
Tell us the pipe size and the bevel
Tri Tool prep equipment & support · On-site service anywhere in North America
300 Series — tube facing and squaring
The high purity workhorses. OD saddle mount, cordless in most cases, and they leave an end square enough to drop straight into a closed weld head. Chips are directed away from the ID, which is the whole point on pharma, semiconductor and food-grade tube. The STS-4 and STS-8 have replaced the old 304 and 306.
Cordless micro facer
300MF
0.125″–0.750″ OD (3.2–19.1 mm) · 0.125″ wall max · 12 V cordless
In-line squaring
STS-1
0.125″–1.125″ OD (3.2–28.6 mm) · 0.125″ wall · 18 V cordless, 115/230 V
Gear reduced
STS-2
0.188″–2.500″ OD (4.8–63.5 mm) · 0.200″ wall · 18 V cordless, 115/230 V
Replaces the 304
STS-4
0.250″–4.500″ OD (6.4–114.3 mm) · 0.250″ wall max · cordless, 115/230 VAC
Replaces the 306
STS-8
0.500″–8.625″ OD (12.7–219.1 mm) · 0.250″ wall max · 115/230 V electric
Short clamping length
301SP
0.125″–1.125″ OD (3.2–28.6 mm) · 0.125″ wall max · air, 18 V cordless or electric
Short clamping length
301.5SP
0.125″–1.500″ OD (3.2–38.1 mm) · 0.125″ wall max · 18 V cordless or electric
Severing — cutting tube in place
Cut tube and thin wall pipe cold, in place, without deforming the wall. Collet and clamshell mounts so a crew can move down a rack instead of breaking the line apart.
Compact severing
572AC
0.250″–2.000″ OD (6.4–50.8 mm) · 0.125″ wall · air, 110/220 V
Sever and square
576AC
2.000″–6.625″ OD (50.8–168.3 mm) · 0.156″ wall · air, 110/220 V
Clamshell tube cutter
550CTC
0.188″–2.000″ OD (4.8–50.8 mm) · 0.055″–0.125″ wall · air, 18 V cordless or manual
Cold saw for tube
The Tube Saw
0.250″–6.625″ OD (6–168 mm) · wall to 0.150″ · 110/220 V or 40 V cordless · 304/316 stainless
Plastic pipe
PolySever 6
Portable severing for plastic pipe · SQM-2AC squaring module kit option
Above 6″
Larger severing machines
Bigger tube and pipe severing — tell us the OD and wall and we will size it
200 Series — end prep and beveling
ID mount and OD mount machines for facing, beveling, counterboring and single point work. The Surefire machines use self-centering radiused pads so Sch 5 and Sch 10 stainless does not go egg shaped in the clamp. The CouponMaster exists purely to prep test coupons — which matters if you are qualifying welders.
Thin wall, no distortion
Surefire 1.5
0.250″–2.000″ (6.4–50.8 mm) · 0.400″ wall max · air or 18 VDC cordless
Thin wall, no distortion
Surefire 4
2″–4″ pipe, Sch 5 and 10 · 0.120″ wall max · 110/220 V electric
Thin wall, no distortion
Surefire 8
3″–8″ pipe, Sch 5 and Sch 10 · 0.148″ wall max · air, 115/230 V
Tight clearance facer
202TS
0.500″–2.000″ (12.7–50.8 mm) · 0.187″ wall max · air drive
ID mount
204B
0.610″–4.500″ (15.5–114.3 mm) · 0.531″ wall max · air, 110/220 V
Cordless 204B
204B-DC
Same ID-mount BEVELMASTER platform, brushless DC cordless drive — no air line on the deck
ID mount
208B
1.503″–8.625″ (38.1–219.0 mm) · 0.875″ wall max · air, 110/220 V, hydraulic
Heavier ID mount
214B
3.310″–14.000″ (84.0–355.6 mm) · 1.406″ wall max · air, 110/220 V, hydraulic
Large bore
216B
5.170″–32.000″ (131.3–812.8 mm) · 1.500″ wall max · air or hydraulic
Large bore
224B
6.813″–42.000″ (173.0–1066.8 mm) · 2.340″ wall max · air or hydraulic
Largest ID mount
236B
11.433″–60.000″ (290.4–1524.0 mm) · 1.312″ wall max · hydraulic
Test coupons
CouponMaster
1.503″–8.625″ (38.1–219.0 mm) · 0.875″ wall max · ID mount, built for weld coupons
600 Series — clamshell split-frame lathes
When the pipe is already in the rack, the machine has to open around it. Split-frame clamshells sever and bevel in-line pipe in a single setup, with low profile bodies for tight rack spacing and heavy wall capacity on the RBL-G2 frames.
Small bore clamshell
601SBCM
1.315″ and below · low profile split frame · air or 18 V cordless
Split frame
602SBCM
1.315″–2.375″ (33.4–60.3 mm) · 0.250″ wall · air or 18 V cordless
Split frame
603SBCM – 603.5SBCM
1.500″–4.000″ (38.1–101.6 mm) · 0.358″ wall · air or 18 V cordless
Heavy wall, small bore
602.5SBM
1.315″–3.000″ (33.4–76.2 mm) · 1.250″ wall · air or 110 V
Split frame lathes
604SB – 606SB
2.375″–6.625″ (60.3–168.3 mm) · up to 1.500″ wall · air, 110/220 V, hydraulic
Split frame lathes
608SB – 612SB
4.500″–12.750″ (114.3–323.9 mm) · 1.500″ wall · air, 115/230 V, hydraulic
Heavy wall, large bore
612RBL-G2 and up
Up to 60″ (1524 mm) on the 660RBL-G2 · heavy wall, out-of-round capable · hydraulic
Boiler, heat exchanger and fittings
Tube sheet work and fitting faces have their own geometry problems. These are the machines built for them.
Boiler machining
BoilerMaster
0.610″–4.500″ (15.5–114.3 mm) · 0.531″ wall max · air, 110/220 V
Cordless boiler work
BoilerMaster DC
Same range, brushless DC cordless drive — no air line up on the scaffold
Boiler pipe and tube
602TSB
1.500″–2.000″ (38.1–50.8 mm) · 0.800″ wall · low profile OD mount, air
Fittings and miters
536 Fitting Machine
OD mount facing and beveling for fittings, with Z-Miter capability · air motor
Walhonde line-up and fit-up clamps
Precise high/low and gap spacing, set mechanically instead of by eye and a hammer. The Elite adds radial rotation for clocking elbows, tees and fittings before anything gets tacked.
Heavy duty
Top Liner Pipe Clamp
2″–72″ (60.3–1828.8 mm) pipe · pipe-to-pipe or pipe-to-elbow line-up
Clocking control
Top Liner Elite
1.315″–12.750″ (33.4–323.9 mm) · radial rotation for clocking fittings
Light to medium duty
Top Liner Gen III
1.315″–12.750″ (33.4–323.9 mm) · pipe-to-pipe, elbows and tees
Weldable lugs
Top Dawg
3/4″ and 1″ · high/low and gap adjustment · carbon or stainless · fits a toolbox
DuraBits and tooling
Coated tool bits that face and square high purity tube ends and hold an edge far longer than uncoated bits — and they throw the chip away from the ID instead of into it. DuraBit 1, 2 and 3 run on the 300 and 500 Series squaring modules, including short and extreme short perch setups; DuraBit 4, 5 and 6 are for the 208B and 214B.
We stock bits, blades, collets and clamping tooling, plus tungsten precision ground to your specification for the welding side of the job.
What we do with Tri Tool equipment
Repair & rebuild
Feed mechanisms, tool slides, bearings, motors, worn collets and mandrels. If it can be rebuilt, we rebuild it.
On-site service
We come to you, anywhere in North America. Your machines never leave the floor and your schedule stays intact.
Tooling & consumables
DuraBits and tool bits, blades, collets, pads and clamping tooling for the machines you already own.
Training & qualification
Operator training on your own equipment, and welder qualification through our CWI testing lab partner.
Tell us the pipe and the bevel.
Diameter, wall, material and how many joints — we will tell you which machine actually fits the job, and what it costs to keep the one you have running.
Call 720-840-5173
info@tigcompany.com
Tri Tool and Walhonde are trademarks of their owners. Specifications from Tri Tool published data.
